Freestanding Training Board Frames for Kilter Board, Tension Board, Moonboard and Spray Walls
If you are installing a training board, the wall frame determines how stable the system will be.
We build freestanding climbing wall frames that allow you to install Kilter Boards, MoonBoards, Tension Boards and spray walls without modifying your building.
Install Any Training Board
Compatible with Kilter Board, MoonBoard, Tension Board and spray wall layouts.
Built for Board Training
Structural steel frame designed to handle dynamic loads generated during board sessions.
No Building Modifications Required
Freestanding structure allows installation without anchoring into the building.
When you install a training board, the frame becomes part of the training system.
Boards like Kilter Board, MoonBoard and Tension Board generate large dynamic loads during climbing sessions. If the wall flexes or moves under load, the board is not performing the way it should.
We design freestanding climbing wall frames so you can install your board setup on a rigid structure that stays stable under repeated use.
We build freestanding climbing wall frames so you can install training boards without modifying your building.
When you install a training board, the wall becomes part of the training system.
Boards generate large dynamic loads during climbing sessions, which means the wall frame must remain stable and consistent under repeated use.
We design freestanding climbing wall frames so you can install Kilter Boards, MoonBoards, Tension Boards and spray walls on a structure built specifically for board training, without needing permanent construction.
Board climbing puts more stress on a wall than typical gym routes.
During training sessions climbers generate force through:
• powerful pulls
• cutting feet
• dynamic movement
• repeated limit attempts
Over time those movements place significant load on the wall structure.
When we design a training board frame, our goal is simple: the structure should remain rigid and consistent no matter how hard you climb.
When you want to install a training board, the biggest constraint is often the building itself.
Many gyms operate in leased buildings where permanent climbing wall construction is difficult or restricted.
By using a freestanding climbing wall frame, you can install your system board without structural building modifications. If your facility layout changes later, the wall can move with you.
If you are installing a training board, the wall frame must provide:
Chompers freestanding climbing wall frames were designed with these requirements in mind, without requiring permanent building construction.
If you are installing a Kilter Board, you will usually want an adjustable climbing wall so you can change the angle for different training styles.
We design freestanding wall frames that allow you to mount the Kilter Board while maintaining the rigidity required for powerful board sessions.
This allows you to run steep board sessions while still being able to adjust the wall angle when needed.
A MoonBoard relies on a fixed hold layout that climbers use all over the world.
Because the board geometry needs to stay consistent, the frame supporting the MoonBoard must remain stable under load.
We build freestanding wall structures that provide the rigidity required for MoonBoard training while allowing you to install the board without permanent construction.
The Tension Board system is designed to work across multiple angles and training styles.
When you install a Tension Board, the supporting wall needs to allow angle changes while still remaining structurally stable.
Freestanding adjustable climbing wall frames make it possible to support these training systems without attaching the wall to the building.
A spray wall gives you the freedom to create your own training problems without relying on a standardised board layout.
Many gyms install spray walls alongside system boards to give climbers more variety in training.
Our freestanding wall frames can support spray wall layouts just as easily as structured board systems.
When we build freestanding climbing walls, the goal is to give you a stable structure for installing climbing boards without permanent construction.
Instead of attaching the wall to the building structure, the frame supports the wall independently.
This allows you to deploy a board setup quickly while keeping your facility flexible for the future.
We've also ensured that installation is fast, easy and stree free. If you want to know more about the board installation, go here
You can install Kilter Board, MoonBoard, Tension Board or spray walls.
We design the structure to remain stable during powerful climbing sessions.
You can install your training board without structural building work.
If you are planning to install a Kilter Board, MoonBoard, Tension Board or spray wall, the wall frame is what determines how stable and reliable the setup will be.
At Chompers, we build freestanding climbing wall frames designed specifically for training boards and board sessions. Whether you are installing a single board or building out a multi board training zone, we can help you choose the right wall configuration for your facility.
Contact us to discuss your board setup, wall sizing and installation requirements.
| Training Board | Typical Wall Type | Angle Range |
|---|---|---|
| Kilter Board | Adjustable climbing wall | 10° to 70° |
| MoonBoard | Fixed or adjustable wall | 25° to 40° |
| Tension Board | Adjustable climbing wall | 10° to 60° |
| Spray Wall | Fixed or adjustable wall | Variable |
The board may be the training system, but the frame determines how well it performs.
